LUXWAVE

Indoor location, through light

Locate, guide, secure and optimise energy, through light.

Your luminaires become the building’s intelligent network.

A module housed in each luminaire: the lighting keeps lighting, locates your teams and equipment down to the room, guides your technicians and matches energy use to actual occupancy.

  • No cameras
  • No rewiring
  • Even with no mobile coverage
  • Encrypted network

Drag the technician, or click a room on the plan.

  • 0 camerasNo images: a badge reads the light, nothing else.
  • 0 data cablesThe Point Service fits inside the luminaire.
  • 1 address per lightBuilding, floor, room: light stops at the wall.

The chain, at a glance

From light to your tools.

How it works, in detail

  1. ZONE B-12
    The luminaire emitsThe Point Service writes the zone’s address into the light.
  2. B-12
    The badge readsUnder the lighting, it reads this address. No cameras, no action needed.
  3. The lighting relaysThe badge sends it back by radio; the Point Services pass it from light to light.
  4. Room B-12 · 10:42
    Your tools receiveThe gateway delivers it to your servers: monitoring, maintenance, digital building model.

Point Service

One module. Everything included.

Housed in the luminaire, it turns each light into an address, a relay and a voice.

The Point Service, between the luminaire’s power supply and the light source.
  1. Everything is insideA single housing, fitted inside the luminaire.
  2. It speaksA built-in loudspeaker, for alarm verification by voice.
  3. It picks up, it relaysIt picks up the badges nearby and passes the information from light to light, even with no mobile coverage.
  4. It emitsIt writes the zone’s address into the light.
  5. It controlsLights on at arrival, dimming, empty zones switched off.
  6. Nothing to wireIt is powered by the lighting: no data cable to run.

On demonstration

123
  1. Luminaire power supply
  2. Point Service
  3. Light source
In its place, inside the luminaire.The Point Service sits next to the power supply. Retrofit or new build, installation needs no data cable.Open the Point Service page

Badge

It reads the light.

Worn by a person or attached to equipment, it reads the address of the light it is under, then transmits it. No cameras, no action needed.

The LUXWAVE badge, in card format.
  1. It reads the addressA window, a sensor: building, floor, room. An address, not an estimate.
  2. It transmitsThe address goes by radio to the neighbouring lights. No action needed: just wear it.
  3. It raises the alertShort press: the alert goes out, with the address. Long press: it is cancelled.
  4. Nothing to rechargeIt runs on a coin cell battery, with no charging port.
  5. Made to be wornOn a lanyard, in a pocket or on a belt.

On demonstration

A LUXWAVE badge worn on a lanyard, over a work jacket.
On a lanyard, under the light.Worn by a person, the badge reads the address without anyone having to think about it.Open the badge page
The same principle, on a person or on equipment: All products

What?

One light, one zone, one function.

Lighting covers the whole building. LUXWAVE turns it into infrastructure: a module, the Point Service, fits inside each luminaire and writes the zone’s address into its light. A worn badge or an attached tracker reads it, then transmits it.

One example, place by place

Offices

The luminaireOpen-plan ceiling light
The zoneNorth open-plan area, row B
The functionLighting and ventilation set by occupancy

Hospital

The luminaireStoreroom luminaire
The zoneEquipment store, 2nd floor
The functionInfusion pump found without searching

Plant room

The luminaireRoom luminaire
The zoneElectrical room, level −2
The functionLone worker protected, alert with location

Warehouse

The luminaireAisle luminaire
The zoneAisle 12, dock 3
The functionForklift located, delivery to the right dock

Your lighting plan is already the map of your uses.

How?

Radio estimates. Light certifies.

Near a wall, a radio position can fall in either of two rooms. Light stops at the wall: the badge is in the room, or it is not.

ROOM AROOM B?
Radio estimatesRoom A or room B? The error circle overlaps the wall.
ROOM AROOM B
Light certifiesRoom B, no doubt: light stops at the wall.
  • In your luminairesThe Point Service fits inside the luminaire, retrofit or new build. No data cables to run.
  • On an encrypted network, designed to resist cyber threatsThe lights relay information from point to point over an OpenThread radio mesh network. The light itself does not leave the room.
  • In your toolsBuilding management system (BMS), maintenance (CMMS), digital building model (BIM), access control: through open interfaces.

How it works, in detail

Why?

Little to install, little to maintain, quick to pay back.

  • Low investmentNo anchors, no data cabling: the Point Service fits inside the luminaire.
  • Quick commissioningThe lighting plan is already the zone plan. Nothing to calibrate room by room.
  • Very little maintenanceEach Point Service is powered by the lighting.
  • Reduced operating costsOne subscription per device, offered by our lighting and integrator partners.
  • A fast paybackControlled lighting reduces the energy bill and pays for the infrastructure.

−49%

lighting energy on average with networked lighting controls, measured across 194 buildings.

Source: Northwest Energy Efficiency Alliance and DesignLights Consortium, 2020. A benchmark published by a third party, not a LUXWAVE result.
What you measure from day one
  • Alert time
  • Equipment search time
  • Occupancy rate by zone
  • kWh per zone per hour

Sectors

Where light goes to work.

Six sectors where LUXWAVE currently has a demonstrator site, an offer or a request in progress.

A piece of equipment leaves the storeroom. Each light locates it, all the way to the room where it is needed.

Hospitals, clinics, care homes for older people

Healthcare

Beds, equipment and care staff: the right room, straight away.

LocateProtectGuideCertifySave energy

See the sector: Healthcare

The technician is guided to the machine, from luminaire to luminaire.

Factories, production sites, construction sites, sensitive sites

Industry and energy

Technicians guided and protected, right where the equipment is.

ProtectLocateGuideCertifySave energy

See the sector: Industry and energy

Two vehicles on the move, one miner working alone: the gallery lighting locates each of them.

Underground mines, tunnels, galleries, buried structures

Mining and underground

Miners and vehicles tracked gallery by gallery, with no mobile network.

LocateProtectGuideCertifySave energy

See the sector: Mining and underground

The lighting comes on as the forklift passes, then switches off behind it.

Warehouses, distribution centres, parcel depots, cold rooms

Logistics

Forklifts, stock and flows tracked in real time.

LocateCertifyProtectGuideSave energy

See the sector: Logistics

Trolleys move along the aisles: footfall shows in front of the gondola end.

Supermarkets, hypermarkets, specialist superstores

Retail

Every trolley located, every aisle measured.

LocateProtectSave energy

See the sector: Retail

A person heads to the meeting room: the room lights up, the empty open-plan floor switches off.

Offices, public buildings, airports, railway stations

Buildings and infrastructure

Actual occupancy: lighting, heating and ventilation matched to need.

Save energyLocateGuideProtectCertify

See the sector: Buildings and infrastructure
Don’t see your sector?

Education and public buildings, data centres, livestock buildings: the same infrastructure applies.

All sectors

Products

Seven devices, one range.

One Point Service per luminaire, worn or attached devices, a gateway to your software.

Open the Products section There, each device turns through 360° and has its own page.

Ecosystem

One technology, a whole value chain.

Lighting, electronics, energy, digital building models, software, operations: LUXWAVE moves forward with those who manufacture, install and operate.

Visible in the field

  • La DéfenseDemonstrator site in an office tower, since March 2026.
  • MontrealShop demonstrator, in a university laboratory specialising in retail customer experience.
  • Trade shows 2026BIM World, VivaTech, IBS: live demonstrations.

LUMISENSE

The France, Quebec, Belgium consortium

Launched at VivaTech in June 2026, LUMISENSE brings together manufacturers, laboratories and operators around one goal: energy-autonomous connected devices, linked to the lighting network.

France Quebec

Technologie Luxwave Canada inc., our subsidiary in Quebec.

It leads LUXWAVE’s North American projects, with its industrial and academic partners in Quebec.

Visit the Canada page

What next?

See the light at work.

A demonstration on site or remotely, based on your lighting plans.

The location, what you want to solve, your timescales: enough to prepare the demonstration. 1,500 characters at most.
Answer in digits.